SAP2000 Professional Course : From Scratch to Pro

Course Curriculum

Chapter 1: Introduction ( Optional )

Lecture 1: Intro Screen of SAP2000

Lecture 2: Setting up Grid in SAP2000

Lecture 3: 3.Define Material and Section Property in SAP2000

Lecture 4: 4.Replication and Move Tool

Lecture 5: 5.Modelling of SLAB section

Chapter 2: Get the Evaluation Version of SAP2000 for Free

Lecture 1: How to get the evaluation version of SAP2000 in minutes

Chapter 3: Simply supported Beam

Lecture 1: Analysis of Simply supported Beam

Chapter 4: 3D Steel space Truss

Lecture 1: Locating the points in SAP2000 for Truss

Lecture 2: How to join the Points

Lecture 3: Final Modelling of Space 3D Truss

Lecture 4: Define Material and Section Property

Lecture 5: Providing the restrains

Lecture 6: Define the Load Pattern

Lecture 7: Define the Load Combination

Lecture 8: Apply the joint load

Lecture 9: Run Analysis

Lecture 10: Design and analysis of Truss member

Chapter 5: Heavy Steel Structure

Lecture 1: Initial setting for structure

Lecture 2: Define the material

Lecture 3: Importing Channel Section

Lecture 4: Importing the I section

Lecture 5: Modify the Grids.

Lecture 6: Modelling the column

Lecture 7: Rotating the Column

Lecture 8: Shear Connected Frame vs Moment Connected Frame

Lecture 9: Concept of secondary Beam

Lecture 10: Modelling upto tertiary beam

Lecture 11: Bracing Completed

Lecture 12: Laterally Unsuppported beam to Laterally Supported Beam

Lecture 13: Area section defined and Modelled

Lecture 14: Define load pattern

Lecture 15: Apply the load

Lecture 16: Replication

Lecture 17: Upper floor SCF AND MCF

Lecture 18: Modelling the secondary beam

Lecture 19: Modelling of tertiary Beam

Lecture 20: Modelling of Beam for Chequered plate

Lecture 21: Cutouts and beams

Lecture 22: Modelling of Chequered plate

Lecture 23: MCF and SCF on roof

Lecture 24: Secondary beam and Braces

Lecture 25: Why do we Provide the Vertical bracing at the start and at the end

Lecture 26: Vertical Bracing

Lecture 27: Basic load defined and applied

Lecture 28: Advance load defined and applied

Lecture 29: Load combination defined and rename

Lecture 30: Restrains for I section

Lecture 31: Analyze and design

Lecture 32: Understanding the Optimization Scope

Lecture 33: Optimization of structure

Lecture 34: Common mistake and solution

Lecture 35: Check Different forces

Chapter 6: Bill board Structure

Lecture 1: Initial setting for Billboard

Lecture 2: Initial Point setup for bill board

Lecture 3: Replication and Draw of the lines

Lecture 4: Divide and draw lines

Lecture 5: Divide lines at joint and connect

Lecture 6: Create Back support of Banner

Lecture 7: Important Concept

Lecture 8: Understanding the banner length

Lecture 9: Banner supporting structure joints

Lecture 10: Joint for full supporting frame

Lecture 11: Modelling part completed

Lecture 12: Define the Material Property

Lecture 13: Import the section table for the very first time

Lecture 14: Import the section Property

Lecture 15: Assign the section property

Lecture 16: Assign the section property to unassigned member

Lecture 17: Extruded View

Lecture 18: Assign the pinned support to the structure

Lecture 19: When we should provide the releases to the member ?

Lecture 20: Assign quickly releases to the member

Lecture 21: Define the Response Spectrum

Lecture 22: Define the load pattern

Lecture 23: Modification in load pattern

Lecture 24: Area Section defined

Lecture 25: Area section drawn

Lecture 26: Wind load applied on shell

Lecture 27: Live Load Applied

Lecture 28: Wind Load below the shell

Lecture 29: Define Response Spectrum Load Case

Lecture 30: Define Load Combination

Lecture 31: Analyze and design

Lecture 32: How to deal with Failed section

Chapter 7: PEB STEEL STRUCTURE

Lecture 1: Understanding the Dimensions and locating the joint

Lecture 2: Define the Material

Lecture 3: Modelling of column at end

Lecture 4: Dividing the Lines

Lecture 5: Modelling of 1st part of PEB shed

Lecture 6: Modelling of 2nd part of PEB SHED

Lecture 7: Finalising the top of PEB SHED

Lecture 8: Replication and extruded view

Lecture 9: Replication of another member