NX CAD + Autodesk Inventor 2023 CAD + Solid Edge 2022 CAD

Course Curriculum

Chapter 1: Introduction

Lecture 1: Introduction

Chapter 2: NX CAD Interface & Sketching

Lecture 1: NX CAD Interface and Concept

Lecture 2: NX Sketch Part 1

Lecture 3: NX Sketch Part 2

Lecture 4: NX Sketch Constrains

Lecture 5: NX Sketch Exercise

Chapter 3: NX Extrude & Revolve

Lecture 1: NX Extrude

Lecture 2: NX Extrude and Revolve

Lecture 3: NX Extrude Exercise

Lecture 4: NX Revolve Exercise

Chapter 4: NX CAD Features

Lecture 1: NX Edge Blend, Draft, Shell, Trim Body, Chamfer, Hole

Lecture 2: NX Modeling Exercise

Lecture 3: Emboss, Emboss Body, Offset Emboss, Groove

Lecture 4: Emboss, Emboss Body, Extract Geometry

Lecture 5: Trim Sheet, Split body, Trim and Extend, Extend Sheet, Divide face, Delete Body

Lecture 6: Offset Face, Offset Surface, Variable Offset, Thicken, Bounding body, Scale

Lecture 7: Project curve, Offset Curve, Offset Curve on face

Lecture 8: Intersection Curve, Bridge Curve, Isoperimetric Curve, Helix, Tube, Swept

Lecture 9: Isoperimetric Curve, Combined Projection, Curve on surface

Lecture 10: Extract Virtual curve, Isocline Curve

Lecture 11: Sweep Features

Lecture 12: Additional Features – Dart, Block, Sphere, Cyl, Cone

Chapter 5: Synchronous Modeling

Lecture 1: Synchronous Modeling

Chapter 6: NX Surface Modelling

Lecture 1: Surface Through Curves

Lecture 2: Surface Through Curves Mesh

Lecture 3: Studio Surface, Fill Surface

Lecture 4: N-Sided Surface

Lecture 5: Law Extension, Extension

Lecture 6: Law Extension, Silhouette Flange

Lecture 7: Four Points Surface, Surface Through Points

Chapter 7: CAD Modelling Exercises

Lecture 1: Modeling Exercise 1

Lecture 2: Modeling Exercise 2

Lecture 3: Modeling Exercise 3

Lecture 4: Modeling Exercise 4

Chapter 8: Assembly & Drafting Overview

Lecture 1: Assembly 1

Lecture 2: Assembly 2

Lecture 3: Assembly 3

Lecture 4: Drafting Overview

Lecture 5: Drafting Title Block

Chapter 9: Solid Edge Sketching & Modelling

Lecture 1: Solidedge Interface

Lecture 2: Sketching (Line – Circle)

Lecture 3: Sketching (Rectangle-Curve-Extend-Trim-Poligon-Split-Fillet -Chamfer – Arc)

Lecture 4: Sketching (Offset – Mirror – Move – Scale )

Lecture 5: Sketching (Dimensions – Relate )

Lecture 6: Extrude and Cut

Lecture 7: Revolve and Revolve Cut

Lecture 8: Draft – Hole – Round – Chamfer

Lecture 9: Thin Wall – Thin Region – Rip – Lip – Web Network – Vent

Lecture 10: Sweep – Helix – Loft

Lecture 11: Sweep Cutout – Helix Cutout – Loft Cutout

Lecture 12: Pattern – Mirror

Lecture 13: Modify Solids

Lecture 14: Surfacing 1

Lecture 15: Surfacing 2

Lecture 16: Surfacing 3

Lecture 17: Surfacing 4

Lecture 18: Surfacing 5

Lecture 19: Modelling Exercise 1

Lecture 20: Modelling Exercise 2

Lecture 21: Modelling Exercise 3

Chapter 10: Solid Edge Assembly & Drafting

Lecture 1: Assembly Overview

Lecture 2: Assembly 1

Lecture 3: Assembly 2

Lecture 4: Assembly 3

Lecture 5: Drafting 1

Lecture 6: Drafting 2

Lecture 7: Drafting 3

Lecture 8: Drafting 4

Chapter 11: Inventor Modelling

Lecture 1: Inventor Interface

Lecture 2: Create Sketch

Lecture 3: Modify Sketch

Lecture 4: Sketch Constrains

Lecture 5: Create Extrude 1

Lecture 6: Create Extrude 2

Lecture 7: Sketch & Extrude Exercise 1

Lecture 8: Sketch & Extrude Exercise 2

Lecture 9: Create Plane

Lecture 10: Revolve

Lecture 11: Revolve Exercise

Lecture 12: Sweep & Loft

Lecture 13: Hole – Fillet – Chamfer – Shell

Lecture 14: Thread – Split – Thicken – Draft – Combine – Direct

Lecture 15: Pattern

Lecture 16: Coil & Rib

Lecture 17: Point & Axis

Lecture 18: Modelling Exercise 1

Lecture 19: Modelling Exercise 2

Chapter 12: Assembly & Drafting

Lecture 1: Assembly 1