Build a Lego Helicopter in SolidWorks 3D CAD

Course Curriculum

Chapter 1: Introduction

Lecture 1: Welcome to the Course

Lecture 2: How to Use This Course

Chapter 2: Stage 1: Building the Fuselage Base

Lecture 1: Creating the Axle

Lecture 2: Making the Right Angle Beam – Part 1

Lecture 3: Making the Right Angle Beam – Part 2

Lecture 4: Building the Friction Pin

Lecture 5: Making the Pin with Bore

Lecture 6: Creating the first Subassembly

Chapter 3: Stage 2: Expanding the Fuselage

Lecture 1: Creating a Longer Axle Using Configurations

Lecture 2: Making the Right Angle Beam

Lecture 3: Creating the Small Bush Part

Lecture 4: Making Stage 2 – The Fuselage

Chapter 4: Stage 3: Adding to the Fuselage

Lecture 1: Creating the Long Pin Part

Lecture 2: Making the Cross Block Connector

Lecture 3: Building Stage 3 – the Upper Fuselage

Chapter 5: Stage 4: Building the Tail Section

Lecture 1: Building the 7-Long Beam

Lecture 2: Making the 5-Long Beam

Lecture 3: Stage 4: Creating the Tail Boom

Chapter 6: Stage 5: Adding the Tail Rotor Transmission Housing

Lecture 1: Making the One-Sided Pin with Bore

Lecture 2: Stage 5: Adding the Tail Rotor Transmission Housing

Chapter 7: Stage 6: Adding the Tail Rotor Transmission

Lecture 1: Creating the 9-Long Axle Part

Lecture 2: Making the Large Bush Part

Lecture 3: Making the Bevel Gear

Lecture 4: Stage 6: Adding the Tail Rotor Transmission

Chapter 8: Stage 7: Building Up the Helicopter Body

Lecture 1: Creating the Two Block with Axle Holes

Lecture 2: Stage 7: Building Up the Main Rotor Hub

Chapter 9: Stage 8: Adding the Helicopter's Nose Section

Lecture 1: Stage 8: Adding the Helicopter's Nose Section

Chapter 10: Stage 9: Making the Cockpit Area

Lecture 1: Create the Right Angle with Curve Part

Lecture 2: Stage 9: Create the Cockpit Side

Chapter 11: Stage 10: Building Up the Cockpit Rear Section

Lecture 1: Make the Three-Long Cross Block Part

Lecture 2: Create the Axle with Bore Part

Lecture 3: Stage 10: Make the Main Rotor Hub Section

Chapter 12: Stage 11: Make the Upper Fuselage

Lecture 1: Create the Four Beam with Extension Part

Lecture 2: Stage 11: Make the Upper Fuselage Section, and Troubleshooting

Chapter 13: Stage 12: Create the Main Rotor

Lecture 1: Creating the 7-Long Axle Part

Lecture 2: Making the Axle Joint Part

Lecture 3: Stage 12: Adding the Main Rotor Shaft

Chapter 14: Stages 13, 14 and 15: Building Up the Other Side of the Helicopter

Lecture 1: Stages 13, 14 and 15: Building Up the Other Side of the Helicopter

Chapter 15: Stages 16 and 17: Making the Tail Rotor Section

Lecture 1: Making the 2-Long Axle Part

Lecture 2: Creating the Tail Fairing Part

Lecture 3: Stages 16 and 17: Making the Tail Section

Chapter 16: Stages 18 and 19: Adding the Tail Section to the Main Assembly

Lecture 1: Making the Pin with Axle Part

Lecture 2: Creating the Tail Rotor Part

Lecture 3: Making the Half Bevel Gear Part

Lecture 4: Stages 18 and 19: Adding the Tail Section

Chapter 17: Stage 20: Starting the Skids

Lecture 1: Creating the Pin with Large Bush Part

Lecture 2: Stage 20: Starting the Skids

Chapter 18: Stage 21: Finishing the Skids and Tail

Lecture 1: Making the Light Stud and Pin with Stud Parts

Lecture 2: Stage 21: Finishing the Skids and Tail

Chapter 19: Stage 22: Finishing the Helicopter and Adding Mechanical Mates

Lecture 1: Making the Main Rotor Blades

Lecture 2: Stage 22: Finishing the Helicopter and Adding Mechanical Mates